BMW K 1200RS Repair Manual Download

Page: 126 / 416

11.40

1100

Measuring crankshaft bearing

play

Measuring radial play

•

Turn the crankshaft to top dead centre at the
bearing to be measured.

•

Take off the bearing cap.

•

Wipe off oil from the bearing journal and bearing
shell.

•

Measure bearing play with Plastigage,

BMW No. 00 2 590

•

Place the Plastigage strip (arrow) over the full
width of the bearing, 6 to 8 mm
(0.2362 to 0.3150 in) away from the centre.

•

Place the bearing cap in position and tighten the
securing screws.

Tightening torque:

Main bearings .............................................. 50 Nm

Note:

Do not turn the crankshaft any more.

•

Remove bearing cap.

•

Compare the width of the strip with the scale
(arrow) in order to determine bearing play.

Radial play .. 0.020…0.056 mm (0.0008...0.0022 in)
Wear limit .............................. 0.130 mm (0.0051 in)

Measuring endplay

•

Install the crankshaft.

•

Screw dial gauge holder (arrow),

BMW No. 00 2 500

, with dial gauge attached

into the tapped hole for the timing case cover.

•

Move the crankshaft backwards and forwards as
far as it will go and take the dial gauge readings.

Endplay ....... 0.080…0.183 mm (0.0032...0.0072 in)
Wear limit .............................. 0.250 mm (0.0098 in)

KR110550

KR110560

KR110570

00 2 500

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands