BMW K 1200RS Repair Manual Download

Page: 290 / 416

33.21

33 17

Removing, disassembling, reas-

sembling and installing rear
swinging arm

33 17

Removing rear swinging arm

–

Remove rear wheel (

36.8).

–

[Without Integral ABS]

Remove inductive signal

transmitter (

61.15).

–

Remove brake caliper and fasten to the rear
frame using a cable tie (

34.5).

–

Remove rear wheel drive unit (

33.7).

•

Loosen the right rear footrest plate.

Important:

Note high loosening torque at lock ring and left/right
threaded rings and bearing studs.

•

Remove circlip (1) and use socket wrench adapt-
er,

BMW No. 33 6 643

, to unscrew the right

threaded ring (6).

•

Remove circlip (1) and loosen lock ring (2)

Important:

Note high loosening torque for lock ring and for the
threaded rings and the bearing studs on left and
right.

•

Loosen the left threaded ring (3) with socket
wrench insert,

BMW No. 33 6 641

•

Loosen bearing studs (5) at left and right.

•

Remove fastener (7) for shock absorber and
press the shock absorber upwards.

•

Remove left and right bearing studs (5).

•

Pull swinging arm (8) away from drive shaft.

KR330330

KR330410

33 6 643

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands