BMW K 1200RS Repair Manual Download

Page: 219 / 416

23.11

23 00

Disassembling gearbox

23 11

Removing gearbox housing

•

Remove oil filler/level check screw (4).

•

Remove oil drain plug (5) and drain the oil from
the gearbox into a suitable tray.

•

Remove breather (1).

•

Unclip cable (arrow) for gear indicator switch (2).

•

Press spring (3) together and take off gear indi-
cator switch (2).

•

Remove selector lever (6).

•

Carefully press back centering pins (arrows),
working from the back of the gearbox.

•

Remove the nine screws (7) securing the cover
to the housing.

•

Insert gearbox into mount,

BMW No. 23 4 700

•

Secure press-off tool,

BMW No. 23 4 780

, to

mount of clutch slave cylinder.

Important:

Avoid damage to the housing cover and painted sur-
faces.

•

Heat the bearing seats in the housing
to 80 °C... 100 °C/176 °F...212 °F).

•

Use press-off tool,

BMW No. 23 4 780

, to sepa-

rate the housing from the housing cover.

KR230020

K41230010

80…100

23 4 700

23 4 780

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands