BMW K 1200RS Page 285 Repair Manual Download

Page: 285 / 416

33.16

33 12

Checking/adjusting backlash

•

Attach measuring fixture (2),

BMW No. 33 2 600

with dial gauge,

BMW No. 00 2 510

, to crown

wheel (3) and secure to the housing with knurled
screw (4).

•

Attach measuring arm (1),

BMW No. 33 2 604

centrally to crown wheel (3).

Note:

Check tooth backlash at three points 120 degrees
apart; turn the bevel pinion with the crown wheel.

•

Press the crown wheel (3) into the housing with
the palm of the hand and turn to and fro to check
tooth backlash.

Backlash:

(Setting without oil
)....................... 0.07...0.16 mm (0.0028...0.0063 in)

•

Compensate for excessive tooth backlash by in-
serting a thinner shim washer (5) or insert a thick-
er one if tooth backlash is insufficient.

33 2 604

KR330230

33 2 600

00 2 510

KR330240

KR330220

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands