BMW K 1200RS Repair Manual Download

Page: 356 / 416

46.22

46 71

Removing/installing footrest

•

Remove lock washer, pin and torsion spring;
take off footrest.

Note:

When installing pin for footrest, grease with

Shell Retinax EP 2

•

Remove footrest pad from footrest.

•

Installation is the reverse of the removal proce-
dure.

Lubricant:

.................................................. Shell Retinax EP 2

Tightening torque:

Footrest pad to footrest.................................. 4 Nm

61 31

Removing/installing brake light

switch

•

Unscrew and remove the brake light switch.

•

Installation is the reverse of the removal proce-
dure.

Note:

The brake light must come on when the rear-wheel
brake starts to slow the wheel.

Tightening torque:

Brake-light switch........................................... 5 Nm

46 71

Removing/installing left footrest

system

Note:

When installing pin for footrest, grease with

Shell Retinax EP 2

Lubricant:

.................................................. Shell Retinax EP 2

Tightening torque:

Footrest to frame.......................................... 20 Nm
Footrest pad to footrest.................................. 4 Nm

46 71

Adjusting left/right footrests

•

Remove the right footrest system (

46.21).

•

Remove the left footrest system.

•

Install the left/right footrest system in the alterna-
tive position.

Note:

Make sure that the left and right footrest systems
are both in either the upper or the lower position.

Adjusting gear shift lever

•

Remove screw (arrow) and reposition the gear
shift lever to suit the altered footrest position.

Tightening torque:

Footrest system to frame.............................. 20 Nm
Gearshift lever ................................................ 8 Nm

KR460290

K41460120

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands