BMW K 1200RS Page 109 Repair Manual Download

Page: 109 / 416

11.23

1100

Removing, disassembling and

assembling piston with conrod

Removing piston with conrod

Note:

Make a note of which pistons belong to which cylin-
ders, and note the installed positions.

•

Press the piston with conrod out of the cylinder
from the crankshaft side.

Disassembling piston

•

Remove the circlip (3) at one side.

•

Press out piston pin (2) with pressing-out tool,

BMW No. 11 6 710

•

Carefully remove piston rings (1) with piston-ring
pliers.

Note:

Note the correct installed positions.

•

Clean the piston.

Checking piston dimensions

•

Measure piston diameter with a micrometer at
distance “

”.

Distance “

” ............................... 10 mm (0.3937 in)

•

Measure piston ring float with feeler gauges.

•

Measure the end gaps of the piston rings in the
cylinder.

For correct float and end gaps,

.............................. see Technical Data (

11.10).

KR110350

KR110360

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands