BMW K 1200RS Repair Manual Download

Page: 256 / 416

31.19

31 42

Installing leading link

•

Press the outer clamp sleeve flush into the
grooved ball bearing.

•

Chill the clamp sleeve and grooved ball bearing
down to at least -10 °C (14 °F).

•

Push the leading link on to the shoulder of the
spacing sleeve.

Note:

Extend the telescopic fork and press the suspen-
sion strut forwards.

•

Heat the frame to approx. 100 °C (212 °F) at the
right pivot bearing seat.

•

Coat the outside surface of the grooved ball
bearing with assembly grease.

•

Install angular-contact ball bearing and clamping
sleeve in frame, using
M 12 threaded rod,

BMW No. 31 5 691

M 12 nut with mount,

BMW No. 31 5 692

and puller sleeve,

BMW No. 31 5 697

by screwing the M 12 threaded rod into the lead-
ing link from the left.

Note:

The cutout on the pulling-in bushing must face out-
wards.

Note:

Pull clamping sleeve and spacing sleeve together
until gap is closed (arrow).

•

Tighten the leading link pivot mounts to the
frame.

Note:

Insert the bolt for the front suspension strut.

•

Tighten the leading link at the clamp sleeve.

Tightening torque:

Leading link to frame
(clean apply Loctite 243) .............. 107 Nm
Leading link to clamp sleeve ........................ 21 Nm

•

Route the wiring harness into the electronic
equipment box.

•

Secure the electronic equipment box and wiring
harness to the frame.

–

Install the Motronic control unit (

13.5).

•

Install the lid of the electronic equipment box.

•

Secure the leading link to the slider tube bridge,
and tighten.

•

Tighten the front suspension strut.

•

Secure the steering damper to the leading link,
and tighten.

•

Attach the front brake pipe to the fairing holder
and the slider tube bridge.

•

Secure the holder for the brake lines to the frame
at the front right.

•

Install the right-hand radiator.

–

Install the right air intake pipe (

46.17).

•

Detach the lifter,

BMW No. 00 1 510

, from the

sump.

–

Install holder for engine spoiler (

46.14).

–

Install engine spoiler (

46.14).

–

Install the fuel tank (

16.5).

Important:

Connect the positive battery terminal first, then the
negative terminal.

•

Connect the earth (ground) lead to the battery.

KR460390

31 5 697

31 5 691

31 5 692

100

KR460460

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands