BMW K 1200RS Repair Manual Download

Page: 155 / 416

13.5

13 61

Removing/installing Motronic

control unit

Warning:

Comply with safety precautions when handling or
working with fuel; note that the fuel lines are pressu-
rised.

–

Remove fuel tank (

16.5).

Important:

Disconnect ground lead from battery and insulate.

•

Remove the fasteners (arrows).

•

Pull Motronic control unit out of central plug.

Note:

Make sure that the seal at the central plug is cor-
rectly seated.

•

Installation is the reverse of the removal proce-
dure.

13 72

Removing/installing intake air

filter (

00.70)

13 62

Replacing air temperature sen-

sor

•

Take off the left side section of the fairing
(

46.10).

•

Disconnect plug (1) of temperature sensor.

•

Remove temperature sensor (2).

•

Install temperature sensor in intake air silencer,
and tighten it.

Tightening torque:

Temperature sensor in
intake air silencer ......................................... 15 Nm

KR130170

KR130120

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands