BMW K 1200RS Page 279 Repair Manual Download

Page: 279 / 416

33.10

•

Position rear wheel drive with retaining fixture,

BMW No. 33 1 510

, upright.

Important:

To prevent the input bevel pinion (1) from being
damaged if it falls out, use a soft underlay.

•

Heat bearing seat to 120 °C (248 °F).

•

Remove input bevel pinion (1).

Note:

If necessary, release input bevel pinion (1) by strik-
ing lightly.

•

Take off thrust washer (2).

33 12

Disassembling input bevel pinion

•

Clamp input bevel pinion (1) into vise with pro-
tective jaws (splines facing upwards).

•

Using puller,

BMW No. 00 7 500

, pull off both

bearings at the same time.

•

Take off radial-thrust bearing (6), roller bearing
cage (5), outer race (4) and inner race (3).

KR330070

120

33 1 510

KR330400

KR330100

00 7 500

KR330130

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands