00.76
•
Turn the engine over and check the relative po-
sitions of the camshaft chain sprockets and the
crankshaft (at TDC).
•
Install the cylinder head cover gasket with the
half-moon cutouts first. The marks at the front
and rear of the gasket and the cylinder head co-
ver must coincide.
•
Apply a thin coat of
Three Bond 1209
at the are-
as where the cylinder head, timing case cover
and cylinder head cover meet and at the half-
moon cutouts (arrows).
L
Note:
Do not forget the contact spring.
•
Install the cylinder head cover. Insert the front
centre screw (timing end, arrow) and both rear
screws (arrows) in order to locate the gasket.
•
Tighten all screws until sealed.
•
Tighten the screws in diagonally opposite se-
quence, working from the inside outwards.
•
Install the cover plate.
X
Tightening torque:
Cylinder head cover ....................................... 9 Nm
Spark plugs.................................................. 20 Nm
Securing screws for cover plate ..................... 5 Nm
•
Install the engine spoiler and left fairing section.
11 00
Replace the lining of the chain
tensioning rail, chain guide rail and
thrust piece (
a
11.18)
(every 60,000 km/37,000 miles)
KR110840
KR110730
Summary of Contents for K 1200RS
