BMW K 1200RS Repair Manual Download

Page: 398 / 416

61.17

61 31

Renewing/adjusting foot brake

light switch

–

Remove the right footrest assembly (

46.21).

•

Disconnect plug (arrow).

•

Open the cable ties.

•

Release the fastener (arrow).

•

Remove brake light switch with cable.

•

Installation is the reverse of the removal proce-
dure. Pay particular attention to the following.

Tightening torque:

Brake-light switch to footrest plate................. 5 Nm

Important:

Make sure that the cable is routed correctly at the
cutout (arrow) in the footrest plate.

Tightening torque:

Footrest to frame.......................................... 20 Nm

Note:

When installing, note the correct positions of the ca-
ble ties.

•

To adjust the brake light switch, loosen
locknut (2).

•

Turn adjusting screw (1) to set distance

“A”

•

Tighten the locknut.

Warning:

Check piston rod blow-by clearance (

34.12).

Setting:

Distance

“A”

.............................. 15 mm (0.5906 in)

KR610320

KR610330

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands