BMW K 1200RS Repair Manual Download

Page: 206 / 416

21.10

•

Installation is the reverse of the removal proce-
dure. Pay particular attention to the following:

•

Clean mating surfaces on the transmission case
and clutch slave cylinder, use new paper
gasket (arrow).

Important:

To prevent the clutch slave cylinder (2) from intaking
air, tighten retaining screws (1) alternately and uni-
formly.

Note:

Install banjo bolt (4) with new sealing ring.

–

Bleed/adjust the clutch (

00.62).

Tightening torque:

Clutch slave cylinder to gearbox .................... 9 Nm
Banjo bolts to slave cylinder........................... 7 Nm

21 52 Removing/installing clutch pushrod

Note:

Pressure line (3) and bleed line (5) remain on the
clutch slave cylinder (2).

•

Remove the clutch slave cylinder (2).

•

Remove paper gasket (6).

•

Pull clutch pushrod (7) out to the rear.

•

Installation is the reverse of the removal proce-
dure. Pay particular attention to the following:

•

Clean mating surfaces on the gearbox housing
and clutch slave cylinder, use new paper gasket.

Important:

To prevent the clutch slave cylinder (2) from intaking
air, tighten retaining screws (1) alternately and uni-
formly.

Tightening torque:

Clutch slave cylinder to gearbox .................... 9 Nm

KL210080

KR210050

KL210080

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands