BMW K 1200RS Repair Manual Download

Page: 134 / 416

11.48

1100

Installing combined oil/water

pump

Important:

Tighten the clutch housing before installing the oil/
water pump, so that the output shaft cannot dam-
age the pump housing.

•

Check that sealing face of the intermediate oil
pump flange is clean and degreased and apply a
thin coat of

Omni VISC 1002

, for example, along

the line shown on the grey shaded area of the
sealing face in the drawing.

•

Place O-ring on water passage.

•

Install the intermediate oil pump flange.

•

Check that sealing face of the pump housing is
clean and degreased and apply a thin coat of

Omni VISC 1002

, for example, along the line

shown on the grey shaded area of the sealing
face in the drawing.

•

Place O-ring on water passage.

•

Position the drive pinion on the output shaft.

•

Install the pump housing and insert the screws
loosely at first.

Note:

Turn the crankshaft to centre the gearwheels, tight-
ening the screws further at the same time.

•

Tighten the screws to specified torque.

•

Check for any noticeable play at any position of
the water pump impeller.

Tightening torque:

Pump housing to crankcase......................... 10 Nm

•

Run the cables for the oil pressure telltale and
water pump temperature sensor through the
hole in the pump housing and connect them.

•

Check that sealing face of the pump housing
cover is clean and degreased and apply a thin
coat of

Omni VISC 1002

, for example, along the

line shown on the grey shaded area of the seal-
ing face in the drawing.

•

Install the pump housing cover and tighten the
securing screws.

Tightening torque:

Pump housing cover .................................... 10 Nm

1100

Installing crankcase cover

•

Apply a thin coat of

Three Bond 1209

at the ar-

eas where the crankcase, intermediate flange
and crankcase cover meet, and to the sealing
faces on the crankcase, timing case cover and
crankcase cover.

•

Install the crankcase cover with gasket.

•

Screw in all bolts until sealed.

•

Tighten the bolts in diagonally opposite se-
quence, working from the inside outwards.

Tightening torque:

Crankcase cover ............................................ 9 Nm

KR110871

KL110010

KR110890

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands