11.14
Removing the oil pressure switch and regulating
element
•
Remove oil pressure switch (11).
e
Important:
To avoid damage to the sealing face of the oil pres-
sure switch, insert an M 12 screw plug (arrow).
•
Apply pressure to the cover of thermostat
housing (15) and remove the snap ring (16).
L
Note:
Place a suitable thrust block on the cover.
•
Remove greased sealing ring (14), regulating
element (13) and coil spring (12).
Installing oil pressure switch and regulating ele-
ment
•
Insert the coil spring, regulating element (oiled
lightly) and a new sealing ring.
•
Place the thermostat housing cover in position,
apply pressure to the cover and insert the snap
ring.
•
Remove the M 12 screw plug and install oil pres-
sure switch (11).
X
Tightening torques:
Oil pressure switch to
oil pump intermediate flange (11) ................. 35 Nm
Water pump temperature sensor (17) ............. 9 Nm
Screw plug M 12 .......................................... 20 Nm
Install the pump shaft with shaft sealing ring and
slipring seal.
L
Note:
Clean the sealing ring seats.
•
Insert pump shaft (5) (lightly oiled) into the hous-
ing.
•
Place sliding sleeve,
BMW No. 11 6 722
, on
pump shaft.
•
Insert shaft sealing ring (6) into the guide sleeve
of pressing-in tool,
BMW No. 11 6 723,
and
press in with the open side facing inwards.
•
Take off the sliding sleeve.
•
Press in slipring seal (7) (free of grease) with
pressing-in tool,
BMW No. 11 6 724
.
Installing water pump impeller
•
Place water pump impeller (9) with spacing
bushing (8) in position. When tightening, hold the
pump shaft to prevent it from turning.
X
Tightening torque:
Water pump impeller .................................... 33 Nm
KR110430
9
8
7
6
5
16 15
14
13
12
11
17
10
Summary of Contents for K 1200RS
