BMW K 1200RS Repair Manual Download

Page: 189 / 416

17.12

Troubleshooting

Coolant overheat warning light comes on.

Check coolant in expansion tank. Is coolant
level too low?

yes

Add coolant.

Check thermostat. Thermostat does not open.
Is the left radiator warmer than the right, and
the coolant pipe to the water pump hot?

yes

Replace thermostat.

Test the water pump. Is water pump faulty?

yes

Repair/replace water pump.

Fan motor does not cut in.

Check fuse F7. Fuse blown?

yes

Replace fuse

Check fan relay. Fan relay defective?

yes

Replace fan relay.

Check electrical circuit. Poor contact/break in
circuit?

yes

Make good contact/eliminate break in circuit.

Check fan motor. Fan motor defective?

yes

Repair/replace fan motor.

Check thermostat. Thermostat does not open.
Is the left radiator warmer than the right, and
the coolant pipe to the water pump hot?

yes

Replace thermostat.

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands