BMW K 1200RS Repair Manual Download

Page: 165 / 416

13.15

Important:

Do not remove retaining plate (5): the screws locate
the throttle-valve stubs.

•

Disengage throttle-closer cable (3) from its pull
(2) at the throttle-valve rail.

•

Remove circlip (4) and remove throttle-closer ca-
ble.

•

Installation is the reverse of the removal proce-
dure. Pay particular attention to the following:

Important:

Route Bowden cables so as to avoid tight bends
and make sure they are not kinked or pinched.

•

Route the two cables parallel; the throttle-opener
cable (1) with green mark always to the outside.

•

Route the Bowden cables beneath the fairing
bracket between the fork tubes and through the
hole in the guide at the radiator.

•

Clip the Bowden cables together at the coloured
mark (arrow).

•

Check that Bowden-cable pulls at throttle-valve
stubs move freely.

•

Check play of Bowden cables, adjust if neces-
sary (

00.36).

Tightening torque:

Injection rail to cylinder head.......................... 9 Nm

K41130010

KL130030

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands