BMW K 1200RS Repair Manual Download

Page: 35 / 416

00.26

00 00

Checking and adjusting the

motorcycle

00 00

Checking the function of side

stand contact switch

•

Switch off the engine.

•

Place motorcycle on its centre stand.

•

Select a gear and switch on the ignition.

–

Temperature gauge warning light lights up.

•

Extend the side stand, observing the tempera-
ture gauge warning light.

–

Temperature gauge warning light goes out (en-
gine control unit switches off).

00 00

Checking the headlight beam set-

ting and adjusting if necessary

Vertical adjustment

Note:

Set the pivot lever only in the centre position (neutral
position).

•

Pivot lever (1) is in centre position.

•

Adjust headlight beam throw with adjusting
screw (2).

Anti-clockwise rotation: ............ longer throw/higher
Clockwise rotation:................... shorter throw/lower

•

Adjust beam throw with a suitable adjuster.

Setting for headlight beam angle adjuster

...................................................-10 cm (-3.937 in)

Setting for headlight beam

.............................................

= -10 cm (-3.937 in)

.............................

= Bulb centre normal position

.................. (basic spring setting, not pretensioned)

Pivot lever (1):

Centre position ...............................neutral position
Bottom position........................ for heavy loads only

Lateral adjustment

•

Adjust left/right angle at screw (3).

41630010

KR630080

KR630060

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands