BMW K 1200RS Repair Manual Download

Page: 333 / 416

36.10

36 32

Checking front/rear wheel rim

for runout

36 32

Checking front wheel rim for

runout

–

Remove tyre.

–

Align the balancer,

BMW No. 36 3 600

, with

knurled screws (2)/level gauge (1).

•

Pass the balancing shaft,

BMW No. 36 3 621

through the front wheel.

•

Screw the balancing shaft up handtight with
knurled nut,

BMW No. 36 3 622

•

Place front wheel on balancer,

BMW No. 36 3 600

•

Lock the balancing shaft at the balancing stand
with the pin (arrow) to prevent it from turning.

•

Install dial gauge,

BMW No. 00 2 510

, in the dial

gauge holder on the balancer and adjust it to suit
the measuring work to be performed.

Note:

Apply the dial gauge,

BMW No. 00 2 510

, only to

the machined inner surface of the wheel rim.

•

Measure vertical or horizontal runout, as applica-
ble.

Maximum wheel rim runout:

Vertical runout........................... 0.5 mm (0.0197 in)
Horizontal runout....................... 0.5 mm (0.0197 in)

KR360080

36 3 600

00 2 510

36 3 621

36 3 622

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands