BMW K 1200RS Repair Manual Download

Page: 276 / 416

33.7

33 10

Removing, disassembling, reas-

sembling and installing rear wheel
drive

Note:

Checking/adjusting the ABS sensor gap is required
after replacement of the following components:
–

ABS sensor ring, brake disc

–

Brake caliper, bracket for ABS

–

Cover of rear wheel drive housing

–

Crown wheel.

–

Remove rear wheel (

36.8).

–

[Without Integral ABS]

Remove inductive signal

transmitter (

61.15).

–

Remove brake caliper and fasten to the rear
frame using a cable tie (

34.5).

–

Remove brake disc (

34.8)

33 10

Removing rear wheel drive

Important:

Never lay the oil-filled rear drive on its side before in-
stallation, or else oil will leak out when the motorcy-
cle is ridden (suction effect).

•

Unscrew the oil filler plug (5).

•

Remove oil drain plug (4) and drain oil into a suit-
able vessel.

•

Loosen reaction link (3) at the rear wheel drive.

•

Release clamping strap (1).

Warning:

Note high release torques for locknut and fixed
bearing stud.

•

Loosen floating bearing stud (6) and locknut (7).

•

Loosen fixed bearing stud (2).

•

Unscrew and remove free (6) and fixed (2) bear-
ing studs.

Warning:

Note inner races of needle bearings.

•

Detach reaction link (3) at rear wheel drive.

•

Disconnect rear wheel drive from drive shaft.

33 17

Replacing taper roller bearing in

rear wheel drive

•

Pull out needle roller bearing (8) with reaction
support,

BMW No. 00 8 572

, and internal puller,

BMW No. 00 8 573

•

Heat neck of housing to 120 °C (248 °F).

•

Press in needle roller bearing (8) with the inner
race on driver,

BMW No. 36 3 700

KR330010

KR330020

00 8 572

KR330320

00 8 573

120

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands