46.28
•
Installation is the reverse of the removal proce-
dure.
L
Note:
See table below for correct order of assembly.
X
Tightening torque:
Gearbox to frame ......................................... 70 Nm
Cross-member to frame at left and right....... 74 Nm
Spring strut, front, to frame .......................... 43 Nm
Spring strut, front, to leading link.................. 43 Nm
Fork bridge to frame
(clean apply Loctite 2701) ............ 130 Nm
Leading link to slider tube bridge
(clean apply Loctite 2701) ............ 130 Nm
Slider tube bridge to slider tube
(clean apply Loctite 243) ................ 21 Nm
Steering damper to leading link .................. 21 Nm
Handlebar holder to fork bridge...................... 9 Nm
Handlebar clamp
(clean apply Loctite 243) ................ 21 Nm
Holder for radiator ........................................ 10 Nm
Clutch slave cylinder ...................................... 9 Nm
Lower cross-tube to frame ........................... 41 Nm
Front footrest holder, left .............................. 20 Nm
Front footrest holder, right............................ 20 Nm
Cable to starter ............................................ 15 Nm
Cable to generator ....................................... 10 Nm
Earth (ground) lead to upper cross-tube......... 6 Nm
Rear footrest holder, left, to frame ................ 21 Nm
Battery carrier, left, to footrest holder ........... 18 Nm
Brake lines.
Brake hoses/lines/banjo bolts ...................... 18 Nm
Swinging arm to frame:
Left and right bearing studs........................ 160 Nm
Right threaded ring .................................... 200 Nm
Left threaded ring ......................................... 10 Nm
Counter-ring, left ........................................ 160 Nm
Spring strut to swinging arm......................... 50 Nm
Spring strut to frame .................................... 43 Nm
Rear wheel drive to swinging arm:
Fixed bearing stud...................................... 160 Nm
Floating bearing stud...................................... 7 Nm
Locknut ...................................................... 160 Nm
Reaction link
To rear wheel drive....................................... 43 Nm
To transverse tube ....................................... 43 Nm
Rear wheel ................................................. 105 Nm
Rear footrest holder, right, to frame ............. 21 Nm
Engine spoiler:
Lower bracket for engine spoiler to engine... 22 Nm
Engine spoiler to lower bracket ...................... 9 Nm
Fairing carrier:
Left and right to frame .................................. 30 Nm
Centre to frame ............................................ 22 Nm
Instrument cluster to fairing carrier ................. 6 Nm
Oil cooler lines to oil cooler .......................... 25 Nm
Intake air pipe to fairing carrier ..................... 10 Nm
Oil cooler ....................................................... 9 Nm
Fuel injection rail to engine block ................... 9 Nm
Fuel tank to frame ........................................ 22 Nm
Rear frame to frame:
Top .............................................................. 41 Nm
Bottom ......................................................... 21 Nm
Battery holder to rear frame, right................... 6 Nm
Holder for fuse box......................................... 9 Nm
Support for seat tray ...................................... 6 Nm
Retaining hoop for exhaust system
To frame....................................................... 24 Nm
To silencer ................................................... 13 Nm
Expansion tank .............................................. 6 Nm
Lock carrier .................................................... 9 Nm
Grab handle ................................................... 9 Nm
Case carrier to frame ................................... 22 Nm
Summary of Contents for K 1200RS
