BMW K 1200RS Repair Manual Download

Page: 257 / 416

31.20

31 42

Removing left leading link pivot

mount

–

Remove the leading link (

31.18).

•

Remove the air guide at the left radiator.

•

Detach the left radiator from its holder and press
it forwards.

•

Remove the fuel injection rail and secure it to the
frame with the wiring harness.

•

Remove throttle-valve rail together with intake air
silencer.

•

Remove circlip for ball thrust bearing.

•

Heat the frame at the left pivot bearing seat to
approx. 100 °C (212 °F).

•

Remove angular-contact ball bearing and spacer
sleeve, using M12 threaded rod,

BMW No. 31 5 691

M 12 nut with mount,

BMW No. 31 5 692

spacer,

BMW No. 31 5 695

support,

BMW No. 31 5 696

puller sleeve,

BMW No. 31 5 697

and M 12 nut.

Note:

The cutout in the pulling-in bushing faces the spac-
ing sleeve.

•

Press the spacing bushing out of the ball thrust
bearing.

31 42

Installing left leading link pivot

mount

•

Press the spacing sleeve fully into the ball thrust
bearing.

•

Chill the spacing sleeve with ball thrust bearing
down to at least -10 °C (14 °F).

•

Heat the frame at the left pivot bearing seat to
approx. 100 °C (212 °F).

•

Apply assembly grease to the outside diameter
of the ball thrust bearing.

•

Install angular-contact ball bearing and spacer
sleeve, using M12 threaded rod,

BMW No. 31 5 691

M 12 nut with mount,

BMW No. 31 5 692

spacer,

BMW No. 31 5 695

support,

BMW No. 31 5 696

puller sleeve,

BMW No. 31 5 697

and M 12 nut.

•

Install the circlip.

•

Install throttle-valve rail complete with intake air
silencer.

•

Install fuel injection rail.

•

Install the left radiator.

•

Install the air guide for the left radiator.

–

Install the leading link (

31.18).

KR460360

31 5 695

31 5 696

31 5 697

31 5 692

31 5 691

100

KR460380

31 5 697

31 5 696

31 5 695

31 5 692

31 5 691

100

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands