BMW K 1200RS Repair Manual Download

Page: 280 / 416

33.11

33 12 Removing needle roller bearing for input
bevel pinion

•

Break or cut open the inner race of the needle
roller bearing.

•

Heat the housing to 130 °C (266 °F).

•

Pull out the outer race of the needle roller bearing
using internal puller,

BMW No. 00 8 573

, exten-

sion,

BMW No. 00 8 575

and reaction support,

BMW No. 00 8 570

33 12 Installing needle roller bearing for input
bevel pinion

•

Heat the needle roller bearing seat to 100 °C
(212 °F).

•

Press in needle roller bearing using drift or the in-
put bevel pinion.

33 12

Assembling input bevel pinion

•

Heat the inner race (2) to 100 °C (212 °F) and
push onto input bevel pinion (1) until sealed.

•

Slide outer race (3) together with roller cage (4)
onto inner race (2).

•

Heat ball thrust bearing (5) to 100 °C (212 °F) and
push onto input bevel pinion (1) until sealed.

•

Allow input bevel pinion (1) to cool.

KR330110

130

LT 33.006

00 8 570

00 8 575

KR330120

00 8 573

KR330130

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands