BMW K 1200RS Repair Manual Download | Manualshive

Page: 67 / 416

background image

00.58

34 00

[Option without Integral ABS]

Changing brake fluid and bleeding
the brake system

(Inspection IV) annual

L

Note:

This description applies for the brake filling and
bleeding unit with extraction of the brake fluid by a
partial vacuum at the brake caliper.
If other devices are used, comply with their manu-
facturers’ instructions.

34 00

Front brake

Force back the brake pistons.

e

Attention:

Do not scrape the wheel – mask it off if necessary.

–

Remove front brake pads. (

a

00.42)

•

Use resetting tool,

BMW No. 34 1 531

, and loca-

tor,

BMW No. 34 1 532

, to force the pistons in

the left and right brake calipers all the way back
and hold them in this position.

Change and bleed the front brake circuit.

e

Attention:

When bleeding the brake system, always begin on
the left side of the motorcycle.

–

Turn the handlebars to the left.

e

Attention:

Do not allow brake fluid to come into contact with
painted parts of the motorcycle, because brake fluid
destroys paint.

•

Take off reservoir cover with rubber diaphragm.

e

Attention:

When adding brake fluid, do not allow it to enter the
holes for the reservoir lid screws.

•

Add brake fluid up to the

MAX

mark (arrow).

e

Attention:

During brake bleeding, make sure that the fluid rep-
lenishing hole is always below the level of the brake
fluid, or else air will be drawn into the brake system.
Bleed the brakes again if this happens.

KR340620

34 1 531

34 1 532

KR340280

«
...
65
66
67
68
69
...
»

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for K 1200RS

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Yoshimura Pages: 7

MAESTRO EDGE 125 PROGRAMMED FI

Brand: HERO Pages: 84

Brand: SSR Motorsports Pages: 39

Brand: SCA Pages: 5

Brand: KTM Pages: 36

Brand: TERMOSCUD Pages: 8

Brand: Aosom Pages: 13

Brand: RIEJU Pages: 52

Brand: Yamaha Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands