12.15
12 41
Installing starter motor
•
Position the starter motor (4) on the intermediate
flange.
•
Connect the earth (ground) lead at the cross-
tube (6), the battery earth (ground) lead (8) and
the earth (ground) lead at the coil (7) with
fasteners (5).
–
Lower the frame (
a
46.31).
•
Connect positive lead (3). Tighten nut (2) and at-
tach cap (1).
•
Connect cables to alternator.
•
Connect earth (ground) lead to upper cross-
tube.
•
Connect plug for side stand switch.
•
Connect the plug for the oxygen sensor.
•
Connect plug for temperature sensor at cylinder
head.
•
Connect plug for gear indicator switch.
e
Important:
Tighten the three fasteners at the clutch slave cylin-
der uniformly and in diagonally opposite sequence,
with the bleed line open at the bleed screw.
•
Install the clutch slave cylinder.
•
Secure the cable tie.
•
Install the clutch bleed line and secure it to the
frame.
–
Install the left/right radiators with fans (
a
17.7).
–
Reconnect plugs and cables for engine and
gearbox.
–
Install the lower cross-tube (
a
46.25).
–
Install drive shaft and swinging arm (
a
33.21).
–
Install the rear wheel drive (
a
33.19).
–
Remove lifter from engine sump.
–
Install fuel injection rail (
a
13.7).
–
Install intake air silencer (
a
13.6).
d
Warning:
Comply with safety precautions when handling or
working with fuel.
–
Install the fuel tank (
a
16.5).
e
Important:
Connect the positive battery terminal first, then the
negative terminal.
Note correct installed position of positive terminal.
–
Install the battery (
a
00.69).
•
Install the battery retaining plate.
•
Install the tool compartment.
–
Install the complete fairing (
a
46.5).
–
Install the seat.
X
Tightening torque:
Starter motor to gearbox .............................. 20 Nm
Plus cable to starter motor ........................... 15 Nm
Earth (ground) lead to cross-tube ................... 6 Nm
KR120100
4
5
1
2
3
6
7
8
Summary of Contents for K 1200RS
