BMW K 1200RS Repair Manual Download

Page: 334 / 416

36.11

36 32

Checking rear wheel rim for run-

out

–

Remove tyre.

–

Align the balancer,

BMW No. 36 3 600

, with

knurled screws (2)/level gauge (1).

•

Attack the mounting device,

BMW No. 36 3 618

to the centering-collar side of the rear wheel.

•

Pass the balancing shaft,

BMW No. 36 3 607

through the rear wheel.

•

Screw the balancing shaft up handtight with
knurled nut,

BMW No. 36 3 619

•

Place the rear wheel on the balancing stand,

BMW No. 36 3 600

•

Lock the balancing shaft at the balancing stand
with the pin (arrow) to prevent it from turning.

•

Install dial gauge,

BMW No. 00 2 510

, in the dial

gauge holder on the balancer and adjust it to suit
the measuring work to be performed.

Note:

Apply the dial gauge,

BMW No. 00 2 510

, only to

the machined inner surface of the wheel rim.

•

Measure vertical or horizontal runout, as applica-
ble.

Maximum wheel rim runout:

Vertical runout........................... 0.3 mm (0.0118 in)
Horizontal runout....................... 0.3 mm (0.0118 in)

KR360050

36 3 600

00 2 510

36 3 618

36 3 607

36 3 619

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands