BMW K 1200RS Repair Manual Download

Page: 118 / 416

11.32

Assembling freewheel

•

The inscription on the needle roller bearing faces
down.

•

Press the needle roller bearing into the freewheel
gear so that distance (x) is the same at both
sides.

Distance “

” ........ 0.2…0.6 mm (0.0079...0.0236 in)

•

Install the cup spring with the larger diameter
facing the layshaft.

•

Insert the freewheel (oiled with engine oil) into the
outer race.

•

Install the outer race (with clamp block facing
cover plate); the cup spring must snap into the
outer race.

•

Install the cover plate.

Tightening torque:

Cover plate................................................... 10 Nm

•

Push the freewheel gear on to the layshaft while
turning it clockwise.

•

Push the thrust washer on to the layshaft.

1100

Removing/installing needle bear-

ings for layshaft and shaft sealing ring
in crankcase

Removing bearing

•

Place support ring,

BMW No. 11 6 731

, in posi-

tion and remove bearing with puller,

BMW No. 00 8 570

, and internal puller 21/3,

BMW No. 00 8 574

•

If a defective bearing cannot be pulled out, care-
fully cut through the needle roller race (with a
grinder).

Removing shaft sealing ring

•

Lever out the shaft sealing ring.

Installing shaft sealing ring

•

Drive in the new shaft sealing ring with a drift,

BMW No. 11 6 732

Installing bearing

•

The inscription on the needle roller bearing faces
outwards.

•

Drive the bearing in with a drift,

BMW No. 11 6 733

KR110180

KR111000

00 8 574

11 6 731

00 8 570

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands