BMW K 1200RS Repair Manual Download

Page: 185 / 416

17.8

•

Disconnect connecting hose (1) to right radiator,
vapour discharge hose (2) and breather hose (3)
at the top of the radiator.

•

Disconnect the coolant hose at the bottom of the
radiator.

•

Pull the radiator with fan out of the lower holder.

•

Installation is the reverse of the removal proce-
dure.

Tightening torque:

Air guide to radiator........................................ 1 Nm

17 11

Removing/installing right radiator

–

Drain coolant (

00.67).

•

Remove the fasteners (arrows).

Note:

If necessary, remove the intake air pipe.

Note:

Illustrations for the following work:

Remove left radiator.

•

Remove retaining clips with washers for radiator.

•

Loosen air outlet guide mountings. Take off air
outlet guide.

•

Disconnect fan plug.

•

Disconnect the coolant hose from the lower stub
pipe (2) on the right radiator.

•

Disconnect connecting hose (1) to left radiator at
the top.

Note:

First detach radiator from holder at left, then sepa-
rate from intake air pipe.

•

Pull radiator with fan away from holder.

•

Installation is the reverse of the removal proce-
dure.

Tightening torque:

Intake air pipe to fairing holder ..................... 10 Nm

KR170040

KR170050

KR170180

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands