BMW K 1200RS Repair Manual Download

Page: 76 / 416

00.67

17 00

Changing coolant

17 00

Draining coolant

–

Remove left side section of fairing, right rear sec-
tion and engine spoiler (

46.10).

•

Open the filler cap on the left radiator.

•

Disconnect the coolant hose (arrow) from the oil/
water pump and drain the coolant.

•

Release fastener (1) and remove and empty the
expansion tank.

•

Slacken fastener (2) for breather hose.

•

Disconnect the breather hose, raise the expansi-
on tank and drain the breather hose completely.

•

Reconnect the breather hose.

Attention:

Dispose of old coolant in an environmentally-friendly
manner.

KR170110

KR170020

KR170010

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands