BMW K 1200RS Repair Manual Download

Page: 344 / 416

46.10

46 63

Removing left and right fairing

side sections

–

Remove the seat (

52.5).

–

Remove inner trim panels (

46.8).

–

Remove upper section of fairing (

46.9).

Important:

Before removing/installing fairing side sections, fit
the protective cap from the on-board toolkit.

•

Fit protective cap (1) onto fairing bracket.

•

Release the fasteners for the left and right side
sections of the fairing.

Note:

The side sections of the fairing are attached at the
tank cover and by the frame at the sides by retaining
pins (arrows).

•

Installation is the reverse of the removal proce-
dure.

Important:

Avoid scratching the paint; when installing the side
sections take special care not to cause damage at
the upper section and the hand protectors.

Note:

See table below for correct order of assembly.

M W

K41460030

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands