BMW K 1200RS Repair Manual Download

Page: 337 / 416

46.3

Technical Data

K 1200 RS

Location of type plate/vehicle identification
number (remove seat)

Left rear frame, inside/bottom right of frame

Length, overall

mm (in) 2,250 (88.5825)

Maximum height in normal position
(without mirrors, windscreen lowered)

mm (in) 1,248 (49.1338)

Width across handlebars

mm (in) 680 (26.7716)

Wheelbase in normal-load position

mm (in) 1,555 (61.2203)

Ground clearance in normal-load position

mm (in) 125 (4.9212)

Wheel offset (rear wheel to right)

Rear wheel 5 x 17"

mm (in) 4.5 (0.1772)

Rear wheel 5.5 x 17"

mm (in) 0 (0)

Caster angle in normal-load position

mm (in) 124 (4.8819)

Steering head angle in normal-load position

° 62.8

Steering lock angle

° min. 30

Dynamic heel angle
(footrests up)

° 44

Dynamic heel angle
(footrests down)

° 41

Axle load distribution (without rider),
front/rear

% 51 / 49

Unladen weight, ready for road, tank full
(without options)

kg (lbs) 285 (628)

Max. payload

kg (lbs) 215 (474)

Permitted total weight

kg (lbs) 500 (1,102)

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands