BMW K 1200RS Repair Manual Download | Manualshive

Page: 48 / 416

background image

00.39

11 00

Changing engine oil, replacing

oil filter element

(Inspections I, II, III and IV)

L

Note:

Change the oil and renew the oil filter at least every
6 months. If the motorcycle is ridden only for short
distances or at outside temperatures below 0 °C
(32 °F), this task must be performed every 3 months
or at the latest every 3,000 km (1,800 miles).

e

Attention:

Note the precautions which must be taken if the en-
gine is run in an enclosed space.
If an engine failure occurs, the oil tank and feed line
must be cleaned with the material used for this pur-
pose in the workshop, and then blown through with
compressed air.

–

Drain the engine oil only when it is at normal ope-
rating temperature.

•

Place the motorcycle on its main (centre) stand,
in a horizontal position.

–

Remove the engine spoiler (

a

46.14).

•

Unscrew the oil filler plug.

•

Remove the oil drain plug from the engine.

•

Drain the oil completely.

•

Remove the screws (2) holding the oil filter cover.

•

Unscrew the oil filter with special wrench (3),

BMW No. 11 4 650

.

•

Unscrew and remove the oil filter.

L

Note:

Always install the oil drain plug with a new sealing
ring.

•

Install the oil drain plug with a new sealing ring
and tighten.

•

Coat the sealing rings on the new oil filter with oil.

•

Screw the oil filter in hand-tight; note the instruc-
tions on the filter.

•

Replace the seal in the oil filter cover if necessa-
ry.

•

Installation is the reverse of the removal proce-
dure.

•

Pour in the specified quantity of oil.

•

Screw in and tighten the oil filler plug.

e

Attention:

Never add engine oil above the “MAX” mark in the oil
level sight glass.

•

Check oil level only at least 10 minutes after
completing a trial run/test drive and stopping the
engine; check the oil level and correct it if neces-
sary.

Operating fluids:

Brand-name HD oil, API classification SF, SG or SH;
suffix letters CD or CE are permitted; alternatively,
brand-name HD oil of CCMC classification G4 or
G5; suffix PD2 is permitted.

Engine oil capacity:

with filter renewal

.......................3.50 l (6.15 Imp. pint/3.70 US quart)

Difference between
MIN and MAX marks on dipstick

.......................0.50 l (0.88 Imp. pint/0.53 US quart)

X

Tightening torque:

Oil drain plug................................................ 30 Nm
Oil-filter cover fastener ................................. 10 Nm
Oil filter......................................................... 11 Nm

KR000010

11 4 650

BMW recommends Castrol

«
...
46
47
48
49
50
...
»

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for K 1200RS

Speedglas G5-02

Brand: 3M Pages: 17

Speedglas 9100 MP

Brand: 3M Pages: 72

Brand: 3M Pages: 84

Brand: NZI Helmets Pages: 4

Brand: GYS Pages: 36

Brand: R&G Pages: 18

Brand: GAS GAS Pages: 69

Brand: rizoma Pages: 16

Brand: Thunderbike Pages: 7

Brand: GAS GAS Pages: 26

Brand: hepco & becker Pages: 2

Brand: KREIDLER Pages: 4

Brand: DYNATEK Pages: 3

Brand: DYNATEK Pages: 6

Brand: AGUSTA Pages: 427

HelmetTalk HTCS-3O

Brand: Nady Systems Pages: 2

Brand: Chicago Electric Pages: 10

Brand: Chicago Electric Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands