BMW K 1200RS Page 301 Repair Manual Download

Page: 301 / 416

34.7

3400

Disassembling and assembling

rear brake caliper

3400

Disassembling rear brake caliper

Attention:

not separate

the brake caliper halves!

•

Drive the retaining pins (3) out towards the wheel
side.

•

Remove pin (2) and spring (1).

•

Remove brake pads.

–

Remove the brake caliper (

34.5).

•

Close the bleed screw.

Tightening torque:

Bleed screw to brake caliper ........................ 10 Nm

•

Hold a cloth over the brake caliper piston.

Attention:

Keep fingers away from gap between piston and
side contact face of brake pads; risk of injury.

•

Carefully

press out brake piston (6) with a com-

pressed air gun applied to the connecting bore;
work at low air pressure.

•

Remove sealing rings from left and right bores.

•

Inspect the brake caliper piston for hairline
cracks, score-marks and other damage.

3400

Assembling rear brake caliper

•

Coat new sealing rings (4, 5) with brake fluid and
insert them into the left and right brake caliper
bores.

•

Coat both brake pistons with brake fluid and in-
stall; force the pistons all the way back.

Attention:

Keep the brake pistons parallel with their bores
when installing.

Note:

Make sure spring (1) is correctly positioned, i.e.
closed at rear (arrow).

–

Install brake caliper (

34.5).

–

Insert brake pads and secure with retainers
(

00.43).

•

Install retaining pins (3) with pin (2) and
spring (1).

RS340133

1
2

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands