BMW K 1200RS Page 107 Repair Manual Download

Page: 107 / 416

11.21

Removing/installing coolant sealing cap at top
of cylinder head

–

Remove the engine spoiler (

46.14).

–

Remove left and right fairing side sections
(

46.8).

–

Drain coolant (

00.67).

•

Remove the heat shield.

•

Pull off spark plug caps with flat pliers.

•

Remove spark plugs from cylinders 2 and 3.

•

Using a punch positioned off-centre (arrow), tap
coolant sealing cap (1) until it is at a right angle in
its bore.

•

Using a punch positioned off-centre (arrow), tap
coolant sealing cap (2) until it is at a right angle in
its bore.

•

Use water-pump pliers to remove coolant seal-
ing caps (1) and (2).

Important:

Do not permit coolant sealing caps to drop into the
coolant system; use a magnetic grab to remove the
sealing caps if necessary.

•

Clean the seating faces for the coolant sealing
caps in the cylinder head.

•

Installation is the reverse of the removal proce-
dure. Pay particular attention to the following:

•

Apply

Loctite 270

to the entire outer circumfer-

ences of coolant sealing caps (1) and (2).

•

Drive in coolant sealing caps (1) and (2) until
seated below bevel, using hammer and drift,

BMW No. 11 6 761

•

Fill the cooling system.

–

Check cooling system for leaks (

17.11).

KR11104

KR111020

KR111010

KR111030

11 6 761

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands