BMW K 1200RS Repair Manual Download | Manualshive

Page: 108 / 416

background image

11.22

1100

Removing crankshaft

L

Note:

Remove the driver first if the intermediate flange is
also to be removed after the crankshaft.

Removing big end bearings

•

Bring pistons 1 and 4 to BDC position.

e

Important:

Make a note of which caps belong to which con-
necting rods, and note the installed positions.

•

Release the connecting rod screws (arrows).

•

Remove the big end bearing caps.

•

Repeat the procedure for cylinders 2 and 3.

Removing main bearings (engine installed)

•

Loosen all but one (arrow) of the main bearing
bolts.

L

Note:

Make a note of which caps belong to which main
bearings, and note the installed positions. Bearing
caps 1 - 3 are marked for identification. Bearing 4
(thrust bearing) and bearing 5 are not marked.
Cylinder 1 = timing end of engine.

•

Take off the bearing caps.

•

Remove the final bolt.

•

Take off the bearing cap, pressing the crankshaft
in towards the crankcase while doing so.

Removing main bearings (engine removed)

•

Remove all main bearing bolts and take out the
bearing caps and the crankshaft.

KL110210

KR110330

«
...
106
107
108
109
110
...
»

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for K 1200RS

Brand: hepco & becker Pages: 4

Brand: CF MOTO Pages: 443

Brand: Nolan Pages: 80

Brand: hepco & becker Pages: 5

Brand: Pagsta Pages: 47

Brand: Tractel Pages: 12

Brand: HYOSUNG Pages: 74

Brand: VOIGT MT Pages: 2

Brand: N-Com Pages: 28

Brand: Petzl Pages: 12

Brand: Beta Pages: 82

Brand: Petzl Pages: 4

PEGASO 650 - 2009

Brand: APRILIA Pages: 60

Brand: KTM Pages: 7

Brand: KTM Pages: 27

390 Duke 2014 COL 2013

Brand: KTM Pages: 204

Brand: Royal Enfield Pages: 104

Brand: HealTech Electronics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands