BMW K 1200RS Repair Manual Download | Manualshive

Page: 62 / 416

background image

00.53

Bleeding the control circuit at the filler adapter

•

Wrap a cloth around filler adapter (1) at the pres-
sure modulator.

•

Remove socket-head grubscrew (arrow) from the
filler adapter.

d

Warning:

When changing and bleeding the control circuit bra-
ke fluid, do not use vacuum extraction.

•

Tighten the bleed screw up to the stop in the filler
adapter (valve in filler adapter closed).

•

Connect the silicon hose with brake bleeding
device to the bleed screw, but

do not switch on

.

e

Attention:

During the bleeding process, the brake fluid level
must not drop below the “MIN” mark, or else air will
be drawn into the brake system. Bleed the system
again if this happens.

•

Open the bleed screw by half a turn (to open the
valve) and bleed the system in accordance with
instructions for bleeding.

•

Remove the bleed screw.

•

Disconnect the brake bleeding device from the
bleed screw.

e

Attention:

The motorcycle must not be ridden without the in-
ternal hexagon grub screw (arrow) screwed into the
filler adapter.

•

Install the socket-head grubscrew in the filler ad-
apter and tighten.

X

Tightening torque:

Grubscrew at filler adapter ........................... 10 Nm

Front metering cylinder

Connect the brake bleeding device to bleed
screw (2), but

do not switch on

.

d

Warning:

When changing and bleeding the control circuit
brake fluid, do not use vacuum extraction.

•

Bleed system using the ring spanner,

BMW No. 34 2 532

, in accordance with

instructions for bleeding.

Front integral circuit

•

Release the fasteners on the battery tray and re-
move the battery tray.

•

Connect special spanner,

BMW No. 34 2 531

,

and silicon hose with bleeding unit to bleed
screw (3), but

do not switch on

.

•

Bleed system using the ring spanner,

BMW No. 34 2 531

, in accordance with

instructions for bleeding.

KL340360

1

KR340660

34 2 532

2

KR340860

34 2 531

3

«
...
60
61
62
63
64
...
»

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for K 1200RS

Brand: Baotian Pages: 30

Brand: Keis Pages: 2

Brand: MadStad Engineering Pages: 2

Brand: hepco & becker Pages: 2

Nils Extreme MTW03

Brand: Abisal Pages: 21

Brand: Husqvarna Pages: 7

Brand: Bosch Pages: 160

Brand: hepco & becker Pages: 2

Brand: Silvercrest Pages: 42

Brand: LSL Pages: 4

Brand: Wunderlich Pages: 4

Brand: Malaguti Pages: 304

Brand: Panther Pages: 47

Brand: Petzl Pages: 3

Brand: Petzl Pages: 11

Brand: Petzl Pages: 11

Brand: cleanAIR Pages: 146

250 EXC Six Days TPI

Brand: KTM Pages: 180

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands