BMW K 1200RS Repair Manual Download | Manualshive

Page: 302 / 416

background image

34.8

3400

[Integral ABS] Removing/

installing front brake disc

d

Warning:

Carefully press back the pistons as you remove/in-
stall the brake callipers as the wheel circuit reservoir
must not overflow.
If fluid escapes, proceed in accordance with “In-
structions for filling reservoir” (

a

00.47).

–

Remove front wheel (

a

36.5).

e

Attention:

Screw is secured with a thread-locking compound.

•

Take out the five fasteners (1) of brake disc (2).

•

Take off brake disc (2) and, at the left, sensor
wheel (3) as well.

•

Installation is the reverse of the removal proce-
dure. Pay particular attention to the following:

e

Attention:

Degrease brake disc (2) before installing.
Note hole pattern on brake disc (2); the arrow points
in the forward travel direction.
Insert screw with

Loctite 243

.

X

Tightening torque:

Brake disc to front wheel
(clean apply Loctite 243) ................ 21 Nm
Brake caliper to fork slider............................ 30 Nm

3400

[Integral ABS] Removing/

installing rear brake disc

d

Warning:

Carefully press back the pistons as you remove/in-
stall the brake callipers as the wheel circuit reservoir
must not overflow.
If fluid escapes, proceed in accordance with “In-
structions for filling reservoir” (

a

00.50).

–

Remove rear wheel (

a

36.8).

–

Remove the brake caliper.

L

Note:

Mark the installed position of brake disc (4) at rear
wheel drive (5), so that vertical runout of the sensor
wheel is not altered.

e

Attention:

Screw is secured with a thread-locking compound.

•

Heat the fasteners (arrows) for brake disc (4) to
120 °C (248 °F).

•

Installation is the reverse of the removal proce-
dure. Pay particular attention to the following:

e

Attention:

Degrease brake disc (4) before installing.
When installing, use new screws or clean the thread
and apply Loctite 2701.
If a new brake disc (4) is installed, the sensor wheel
must be re-marked.

L

Note:

Checking/adjusting the ABS sensor gap is required
after replacement of the brake disc.

–

If required, check/adjust ABS sensor gap
(

a

34.11).

X

Tightening torque:

Brake disc to rear wheel drive (new screws or clean
apply Loctite 2701) ........................ 21 Nm
Brake caliper to rear wheel drive .................. 40 Nm

KR340190

2

2

3

1

KR340100

4

w

h

120

5

«
...
300
301
302
303
304
...
»

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for K 1200RS

Brand: Caberg Pages: 16

Brand: Ohlins Pages: 4

Brand: DMC Pages: 2

Brand: Happy Trails Pages: 4

Brand: KYMCO Pages: 55

Brand: MOTO GUZZI Pages: 266

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 114

Brand: Yamaha Pages: 168

Brand: Yamaha Pages: 497

Brand: Yamaha Pages: 704

Brand: Yamaha Pages: 84

Brand: hepco & becker Pages: 3

Brand: Malaguti Pages: 272

Brand: Montesa Pages: 114

4Ride MST260 2016

Brand: Montesa Pages: 158

Brand: Kobalt Pages: 33

Brand: VESPA Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands