BMW K 1200RS Page 415 Repair Manual Download

Page: 415 / 416

63.6

63 12

Replacing bulbs in headlight

Note:

Never touch the glass of the bulb with the fingers.

•

Press the retaining hoop (1) down. Take off the
housing cover (2).

•

Renew the high (main) beam (3), low (dipped)
beam (4) or parking light (5) bulb.

•

Place the housing cover in position and engage
the retaining loop.

63 13

Renewing front turn indicators

63 13

Removing/installing front turn

indicator

•

Release the fastener (1) and remove the turn in-
dicator.

•

Installation is the reverse of the removal proce-
dure.

Note:

When installing, make sure that the lug (arrow) is
correctly seated.

63 12

Changing the bulb

Note:

Never touch the glass of the bulb with the fingers.

•

Remove the appropriate turn indicator. Change
the bulb.

KR630020

K41630030

K41630040

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands