BMW K 1200RS Page 66 Repair Manual Download

Page: 66 / 416

00.57

34 00

[Option without Integral ABS]

Checking brake fluid level front and
rear

(Inspections II and III)

Note:

Gradual wear of the brake pads causes the brake
fluid level in the reservoir to sink.

34 00

Checking brake fluid level

(front brakes) at handlebar fitting

•

Place motorcycle on side stand.

•

Centre the handlebars.

•

Check brake fluid level at sight glass.

Warning:

Never permit the brake fluid level to drop below the
minimum level on the brake fluid reservoir.

Minimum level

Condition for reading
Motorcycle resting on its side stand
Handlebars centred

MIN

...........................................Lower ring marking

Specified level with new brake pads

Condition for reading:
Motorcycle resting on its centre stand
Handlebars turned fully to the right

Specified level

.........................Upper ring marking

34 00

Checking the rear brake fluid level

Note:

The volume of the brake fluid (

MIN/MAX

) is suf-

ficient for pad thicknesses from new to the wear li-
mit. It is not normally necessary to add fluid to
compensate for pad wear.
A level below

MIN

indicates the possibility of other

faults.

–

Place motorcycle on its centre stand.

Attention:

The fluid level in the brake fluid reservoir must be at
the

MAX

mark with new brake pads.

•

Check brake fluid level in the reservoir.

•

The brake fluid level must never fall below the mi-
nimum level.

•

Check that the brake system is properly sealed if
the brake fluid level is below the

MAX

mark with

new brake pads.

Specified level with new brake pads

............

MAX

Brake fluid

...................................................DOT 4

K41000040

MIN

KR340290

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands