BMW K 1200RS Page 4 Repair Manual Download | Manualshive

Page: 4 / 416

background image

Use

Each chapter starts with the list of contents.

The list of contents is followed by the Technical Data table.

Key to symbols

In this Repair Manual for the K 1200 RS model, the following symbols are used; their meanings are ex-
plained in the table.

Special instructions aimed at improving the work procedures

L

Note:

Specific information on operating, inspecting and adjusting work for the motorcycle as well as maintenance
procedures.

e

Important:

Instructions and precautions specifically intended to prevent damage to the motorcycle. Failure to comply
with them could invalidate the warranty.

d

Warning:

This symbol stands for precautions and measures which are essential in order to protect the rider or other
persons from possibly severe or fatal injury.

Contents

The titles of the tasks described in this chapter............. complete with page numbers

Activities

•

Activities

•

The bullet symbol means that work steps are described in greater detail under another headline

–

Preceding activities

–

A line indicates work steps described in greater detail under another headline or in another chapter

If the term “undo” or “remove” is used:
the fastener (e.g. screw) must be slackened off and taken out
or
a component (e.g. fuel rail) must be removed to the extent that other components which it conceals (e.g.
throttle valve rail) are accessible

If the term “loosen” or “slacken” is used
the fastener (e.g. screw) must only be slackened off but not taken out

X

Tightening torques:

Values are stated if they differ from DIN EN 24 014 or DIN 912 ISO industrial standards.

«
...
2
3
4
5
6
...
»

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for K 1200RS

Brand: Xenith Pages: 17

Brand: Honda Pages: 112

Brand: R&G Pages: 13

Brand: Sicor Pages: 2

Brand: Yamaha Pages: 122

Brand: Yamaha Pages: 142

Brand: Yamaha Pages: 118

Brand: Husqvarna Pages: 241

Brand: Husqvarna Pages: 279

Brand: Husqvarna Pages: 162

Brand: Husqvarna Pages: 163

Brand: Husqvarna Pages: 158

Supermoto 701 2021

Brand: Husqvarna Pages: 278

FC 250 Rockstar Edition 2022

Brand: Husqvarna Pages: 151

Brand: Husqvarna Pages: 169

Brand: Husqvarna Pages: 184

Brand: Husqvarna Pages: 286

TC 250 2012 I.E. USA

Brand: Husqvarna Pages: 376

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands