BMW K 1200RS Page 106 Repair Manual Download

Page: 106 / 416

11.20

•

Remove valve collets (1) with a magnetised
screwdriver.

•

Release valve spring clamp (3) and take out up-
per spring retainer (2), valve spring and lower
spring retainer (4).

•

Take out the valve stem seal with special pliers,

BMW No. 11 1 250

Remachining valve seat

D = valve diameter
B = valve seat width

•

When remachining, the correct width of the valve
seat must always be maintained.

Note:

Machine the valve seat with turning tool,

BMW No. 11 0 500

•

If the valve seat has been remachined, a new
valve must be installed.

Installing valve and valve stem seal

Note:

If a valve is removed, the valve stem seal must be re-
newed.

•

Oil the stem when installing the valve.

•

Insert the lower spring retainer.

•

Place a shrink-fit tube approx. 20 mm (0.7874 in)
long, on the valve stem and heat it up.

•

Drive in valve stem seal (1) with the assembly
tool,

BMW No. 11 1 602

, until resistance is felt.

Important:

Remove the shrink-fit sleeve from the valve stem.

•

Insert the valve spring.

•

Install the upper spring retainer.

Important:

Centre the compressor in order to avoid damaging
the tappet bores.

•

Compress the valve spring, lightly oil the valve
collets and insert them, then release the spring.

•

Clean and oil the bucket-type tappets before in-
serting.

KR110300

KR110310

KR110320

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands