BMW K 1200RS Repair Manual Download | Manualshive

Page: 316 / 416

background image

34.22

•

Very gently press the handbrake lever until the
pump just starts up.

•

Open the bleed screw at the left-hand brake cal-
iper.

•

Pump the brake fluid at virtually no pressure until
the hose is full of brake fluid.

•

Position the end of the hose on the
cover,

BMW No. 34 2 541

.

•

Pump the brake fluid with virtually no pressure to
begin with, then vary the brake pressure.

d

Warning:

The brake fluid must not foam in the hose.
If this should happen, follow the procedure for
bleeding/changing brake fluid in the front wheel cir-
cuit (

a

00.45).

•

Pump brake fluid through the system until it is
clear and free from air bubbles.

•

Close the bleed screw.

•

Release the handbrake lever.

•

Disconnect silicon hose,

BMW No. 34 1 560

,

from bleed screw and drain its contents into
wheel circuit reservoir.

•

Connect silicon hose,

BMW No. 34 1 560

, to

bleed nipple of right brake caliper.

•

The procedure for bleeding the right brake cali-
per is the same as that for the left caliper.

•

Close the bleed screw.

•

Release the handbrake lever.

•

Switch off the ignition.

•

Disconnect silicon hose,

BMW No. 34 1 560

,

from bleed screw and drain its contents into
wheel circuit reservoir.

•

Remove cap,

BMW No. 34 2 541

.

e

Attention:

After changing and/or bleeding the brakes, always
top up the fluid in the wheel-circuit reservoir to the
correct level in accordance with the instructions.

•

Fill front wheel-circuit reservoir with brake fluid in
accordance with instructions (

a

00.47).

•

Perform a function check on the brake system
with the ignition switched on.

e

Attention:

After all the work on the brake system has been
completed, run a bleed test using the

BMW

MoDiTeC!

•

Perform bleed test with

BMW

MoDiTeC

(

a

00.35).

Brake fluid

...................................................DOT 4

X

Tightening torque:

Bleed screw to brake caliper .......................... 7 Nm

«
...
314
315
316
317
318
...
»

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for K 1200RS

Brand: Free Spirits Pages: 32

Apache RTR 160 HYPER EDGE 2015

Brand: TVS Pages: 60

Brand: Suzuki Pages: 440

HIGHSIDER VICTORY

Brand: Paaschburg & Wunderlich Pages: 5

Brand: Jialing Honda Pages: 10

Brand: yasuni Pages: 12

SEMIFAIRING BATWING SML TOURING

Brand: PUIG Pages: 3

Brand: hepco & becker Pages: 7

Brand: SHERCO Pages: 102

Brand: Suzuki Pages: 165

TorqDrive Clutch Pack

Brand: Rekluse Pages: 18

Brand: MRA Pages: 6

Aquila GT250 R Ej

Brand: HYOSUNG Pages: 37

Brand: Wunderlich Pages: 5

Brand: Sealey Pages: 2

Brand: Malaguti Pages: 50

Brand: Malaguti Pages: 112

Brand: ArcPro Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands