BMW K 1200RS Repair Manual Download Page 52 | Manualshive

Page: 52 / 416

BMW K 1200RS Repair Manual Download Page 52

00.43

Replacing rear brake pads

•

Remove cover from brake caliper.

•

Remove retaining pins (7) from the wheel side.

•

Remove pin (5) and spring (6).

•

Force back the piston with the inner brake pad.

•

Fit new inner pad.

•

Press back outer pad.

•

Fit new outer pad.

L

Note:

Make sure spring (6) is correctly positioned, i.e. clo-
sed at rear (arrow).

•

Install retaining pins (7) with pin (5) and
spring (6).

•

Install protective cap.

L

Note:

After switching on the ignition, always wait for the
BMW Integral ABS to complete its self-diagnosis.
Do not operate the brake lever until self-diagnosis
has completed.

•

Bed in pads with the ignition switched on.

•

Perform a function check on the brake system
with the ignition switched on.

34 00

[Integral ABS] Checking brake

fluid level at handlebar fitting

(Inspections II and III)

L

Note:

The brake fluid level in the sight glass/brake fluid le-
vel remains constant despite wear of the brake
pads.
If the level drops below the MIN mark, this indicates
some other fault.

•

Place the motorcycle on its centre stand.

•

Turn the handlebars to the left.

Specified level

not below ......................................................... MIN
(top edge of the marking ring)

Brake fluid

...................................................DOT 4

KR340

5

7

6

K41000060

MIN

«
...
50
51
52
53
54
...
»

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands