manualshive.com logo in svg

BMW K 1200RS, Repair Manual

The BMW K 1200RS Repair Manual is the comprehensive guide for motorcycle enthusiasts seeking to maintain and fix their BMW K 1200RS model. This essential manual provides step-by-step instructions and detailed diagrams to aid in repairs and maintenance tasks. Download your free copy from our website, manualshive.com.

Share
Download
background image

00.17

Contents

Page

00

General view of crated motorcycle 

.................................................................................. 19

Checking the shipping crate for damage 

.....................................................................20

Damage discovered in Germany

 ............................................................................................20

Damage discovered in importer markets

 ............................................................................20

Unpacking the motorcycle 

....................................................................................................21

General instructions 

.................................................................................................................21

Pushing the motorcycle onto a workshop platform

 .......................................................21

Inspecting motorcycle for damage 

..................................................................................21

Checking that delivery is complete 

..................................................................................21

Installing remaining items on motorcycle 

....................................................................22

Installing the windscreen

 ...........................................................................................................22

Installing mirrors, left/right

 .........................................................................................................22

Installing bracket for engine spoiler

 ......................................................................................23

Installing the engine spoiler

 ......................................................................................................23

Filling and charging the battery 

.........................................................................................24

Remove the battery  ...........................................................................................................................24
Filling and charging the battery ..........................................................................................................24
Installing the battery  ..........................................................................................................................24

Checking tyre pressures 

........................................................................................................25

Checking tightness of rear wheel studs 

........................................................................25

Checking and adjusting the motorcycle 

........................................................................26

Checking the function of side stand contact switch

 .....................................................26

Checking the headlight beam setting and adjusting if necessary

 ..........................26

Vertical adjustment  ............................................................................................................................26
Lateral adjustment .............................................................................................................................26

Installing the seat

 ..........................................................................................................................27

Adjusting seat

 .................................................................................................................................27

Adjusting the handlebars, left/right

 .......................................................................................27

00 Pre-delivery check

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for K 1200RS

SRC S-VS-09-01-AL Quick Start Manual preview
S-VS-09-01-AL
Brand: SRC Pages: 5
SUR-RON Light Bee Service Manual preview
Light Bee
Brand: SUR-RON Pages: 50
R&G CR0076BK Fitting Instructions Manual preview
CR0076BK
Brand: R&G Pages: 9
Suzuki Intruder VS700 Service Manual preview
Intruder VS700
Brand: Suzuki Pages: 526
JIMS MILWAUKEE-EIGHT 5833 Instruction Sheet preview
MILWAUKEE-EIGHT 5833
Brand: JIMS Pages: 10
MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual preview
Stelvio 1200 MY11 2011
Brand: MOTO GUZZI Pages: 385
DYNATEK DDK3-4 Installation Manual preview
DDK3-4
Brand: DYNATEK Pages: 12
Takegawa 02-01-0281 Instruction Manual preview
02-01-0281
Brand: Takegawa Pages: 2
Bosch DISBLAY DDU 7 Manual preview
DISBLAY DDU 7
Brand: Bosch Pages: 160
Dynajet 200iP Installation Manual preview
200iP
Brand: Dynajet Pages: 20
VESPA S 150 2008 Manual preview
S 150 2008
Brand: VESPA Pages: 82
VESPA PX 125 Manual preview
PX 125
Brand: VESPA Pages: 64
Innovv C5 User Manual preview
C5
Brand: Innovv Pages: 2
ArcPro 20702 Instruction Manual & Parts Catalogue preview
20702
Brand: ArcPro Pages: 7
MZ 125 SM Repair Manual preview
125 SM
Brand: MZ Pages: 204
KTM 250 SX 2019 Owner'S Manual preview
250 SX 2019
Brand: KTM Pages: 158
Royal Enfield 2006 Thunderbird TwinSpark Owner'S Manual preview
2006 Thunderbird TwinSpark
Brand: Royal Enfield Pages: 65
Royal Enfield II Series Workshop Maintenance Manual preview
II Series
Brand: Royal Enfield Pages: 60

Brands by name

Popular brands

Load more brands