BMW K 1200RS Repair Manual Download

Page: 304 / 416

34.10

3400

[Integral ABS] Removing/

installing rear ABS sensor

–

Remove rear wheel (

36.8).

Attention:

Disconnect ground lead from battery and insulate.

–

Clean ABS sensor (2) and the hole before remov-
ing/installing.

•

Unscrew ABS sensor (2) from brake caliper (1).

•

Take off ABS sensor (2) with spacing plate (3).

•

Remove all cable ties holding the ABS sensor
cable (4).

•

Disconnect plug connector (arrow) from ABS
sensor cable (4).

•

Installation is the reverse of the removal proce-
dure. Pay particular attention to the following:

Attention:

Carefully route the ABS cable and secure in position
with cable ties.

–

If required, check/adjust ABS sensor gap
(

34.11).

KR340080

KR340210

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands