BMW K 1200RS Page 237 Repair Manual Download

Page: 237 / 416

23.29

23 00

Aligning right-hand rubber mount

Important:

It is not necessary to re-align the right-hand rubber
mount unless the gearbox, the frame or the left-
hand rubber mount has been replaced.

•

Install the right-hand bearing bushing, but do not
tighten the securing screws.

•

Position gearbox against intermediate flange and
tighten securing screws.

•

Lower the frame.

•

Screw the left/right engine mountings to the
cross-member.

•

Install and tighten bolt securing gearbox to
frame.

Important:

To avoid damaging the spacing plate in the clamp
slot, uniformly tighten the left and right pinch bolts.

•

Uniformly tighten the pinch bolts (3) securing the
right-hand rubber mount.

Tightening torque:

Pinch bolt for rubber mount............................ 9 Nm

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands