21.9
•
Centre clutch plate (3) with centering pin,
BMW No. 21 2 673
.
•
Tighten retaining screws (1) in succession, in di-
agonally opposite sequence.
Lubrication points:
Splines on clutch plate and input shaft.
Diaphragm spring contact surface on clutch hous-
ing.
Diaphragm spring contact surface on pressure
plate.
............................................... Optimoly paste MP 3
X
Tightening torque:
Housing cover to clutch housing .................. 12 Nm
–
Install the gearbox (
a
23.10).
–
Install starter motor (
a
12.13).
–
Install transverse tube (
a
46.25).
–
Install front drive shaft (
a
33.23).
–
Install swinging arm (
a
33.24).
–
Install the rear wheel drive (
a
33.19).
–
Install brake caliper (
a
34.5).
–
[Without Integral ABS]
Install inductive signal
transmitter (
a
61.15).
–
Install the rear wheel (
a
36.8).
21 52
Removing/installing clutch slave
cylinder and pushrod
Removing/installing clutch slave cylinder
–
Remove rear wheel (
a
36.8).
–
[Without Integral ABS]
Install inductive signal
transmitter (
a
61.15).
–
Remove brake caliper, fasten to the rear frame
with the sensor using a cable tie
(
a
34.5).
–
Remove rear wheel drive unit (
a
33.7).
–
Remove the front section of the rear carrier
(
a
46.7).
–
Remove swinging arm (
a
33.21).
e
Important:
To prevent the clutch slave cylinder (2) from intaking
air, release retaining screws (1) alternately and uni-
formly.
•
Release fasteners (1).
•
Pull clutch slave cylinder (2) away from gearbox.
•
Remove paper gasket.
•
Release banjo bolt (4), remove pressure line (3)
and bleed line (5).
21 2 672
KR210040
21 2 673
KR210050
1
1
1
4
5
3
2
Summary of Contents for K 1200RS
