BMW K 1200RS Repair Manual Download

Page: 36 / 416

00.27

00 00

Installing the seat

Attention:

When installing, make sure that the seat is retained
firmly.

•

Push the seat tongue under the seat support.

•

At the rear end, guide the seat carefully into the
first detent position of the catch.

•

At the front, push the seat into the lower or upper
guide (depending on the rider’s height).

•

Press down on the rear end of the seat to engage
the second detent position of the catch.

00 00

Adjusting seat

Attention:

When installing, make sure that the seat is retained
firmly.

•

Turn key in seat lock to left and hold it there.

•

Pull the seat upwards and to the rear out of its
catch, as far as the first detent position.

•

At the front, push the seat into the lower or upper
guide (depending on the rider’s height).

•

Press down on the rear end of the seat to engage
the second detent position of the catch.

00 00

Adjusting the handlebars, left/

right

Warning:

Do not twist the handlebars, because this leads to
air getting into the brake circuit or hydraulic circuit
of the clutch.

•

Loosen the screw (arrow) and pull the handlebar
out of the splines.

•

Set the new position and retighten the screw.

Note:

The handlebars must always be adjusted symmetri-
cally. Make sure that lines and cables run correctly.
Avoid damage to electrical wiring.

Tightening torque:

Handlebars, left/right.................................... 20 Nm

K41UB0070

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands