BMW K 1200RS Repair Manual Download | Manualshive

Page: 307 / 416

background image

34.13

34 51

[Integral ABS] Removing/

installing pressure modulator

e

Attention:

Work on the ABS pressure modulator may only be
performed by a specialist workshop.

e

Attention:

Do not allow brake fluid to come into contact with
painted parts of the motorcycle. Brake fluid destroys
the paint finish. Protect parts on the handgrip, pres-
sure modulator and brake caliper with cloths.

e

Attention:

Disconnect the negative battery terminal first, then
the positive terminal.

–

Drain the brake system (

a

34.16).

–

Remove battery with hose protector (2)
(

a

00.69).

–

Disconnect plug from power socket in
mudguard.

–

Remove rear mudguard.

–

Slacken diagnosis plug.

e

Attention:

Do not allow brake fluid to come into contact with
painted parts of the motorcycle, because brake fluid
destroys paint.

•

Release hose clips (arrows) at wheel-circuit
reservoir (1).

•

Open 3 cable ties (arrows) on rear frame.

•

Disconnect brake line (8) from distributor filler
adapter (10).

•

Release the fastener (7).

•

Remove clamps and loosen rubber boots on
brake lines (3,4,5).

•

Loosen brake lines (3,4,5).

•

Release 2 fasteners (9) securing pressure modu-
lator to battery holder.

•

Push ABS plug connector (11) to the right to
release (arrow) and remove.

KR340710

1

2

KR340720

7

9

10

8

5

4

3

6

KR340730

11

«
...
305
306
307
308
309
...
»

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for K 1200RS

Brand: hepco & becker Pages: 2

Brand: A.J.S. Pages: 104

Brand: DUCATI Performance Pages: 5

2001 GSX1300RK1 HAYABUSA

Brand: Suzuki Pages: 31

Brand: AGV Pages: 45

Brand: N-Com Pages: 2

Brand: DYNATEK Pages: 11

Brand: Shad Pages: 12

Brand: Baotian Pages: 26

Brand: yasuni Pages: 12

Brand: HYOSUNG Pages: 74

Brand: VOIGT MT Pages: 2

Brand: B&G electronics Pages: 5

Brand: Oxford Pages: 40

HotGrips OF690 Adventure

Brand: Oxford Pages: 42

Brand: OKBABY Pages: 35

Brand: R&G Pages: 20

Brand: Janus Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands