BMW K 1200RS Page 64 Repair Manual Download

Page: 64 / 416

00.55

34 00

[Integral ABS] Replacing brake

fluid in the rear control circuit/bleeding

Note:

The rear wheel circuit and control circuit have a
shared expansion tank.
The wheel circuit must be filled with brake fluid.

•

Remove the cover (3) from the reservoir (4).

Attention:

During the process, do not permit the brake fluid le-
vel to drop below the hose level or else air will be
drawn into the brake system.

Warning:

If the brake-fluid level in the reservoir does fall below
hose level, the wheel circuit must be refilled at the
brake caliper and bled once again (

34.17).

Note:

Same procedure via other bleed screws as on front
control circuit, metering cylinder and integral
circuits.

Warning:

When performing maintenance and repair work on
the BMW Integral ABS, avoid rapid and forceful
pumping of the brakes.

•

In sequence, bleed the:

–

rear dosing cylinder (1),

–

rear integral circuit (2)

–

rear control circuit (3) and,

–

again, rear dosing cylinder (1)

bleed the system in accordance with instructions for
bleeding.

Regulations for bleeding:

1. Pull the brake lever slowly until the brake light

switch clicks (snifter hole closed).

2. Open the bleed screw.
3. Pull the brake lever fully and close the bleed

screw.

4. Release the brake lever slowly.
5. Repeat steps 1 to 4 until the brake fluid is clear

and has no bubbles.

Rear metering cylinder

•

Use special ring spanner

BMW No. 34 2 532

and connect silicon hose with brake bleeding
device to bleed screw (1), but

do not switch on

Warning:

When changing and bleeding the control circuit
brake fluid, do not use vacuum extraction.

•

Bleed system using the ring spanner,

BMW No. 34 2 532

, in accordance with

instructions for bleeding.

KR340571

MAX

MIN

MAX

KR340670

34 2 532

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands