manualshive.com logo in svg

BMW K 1200RS, Repair Manual

Share
Download
BMW K 1200RS Repair Manual Download Page 129

11.43

1100  

Installing cylinder head

L

 Note:

Remove the bucket tappets before installing the cyl-
inder head. Make a note of which bucket-type tap-
pets belong to which valves.

•

Clean the cylinder head bolts and the threads in 
the engine block.

•

Clean the sealing faces and check for surface ir-
regularities and damage.

e

 Important:

When installing a new cylinder head, check the seal-
ing faces and make sure they are free of burrs, pay-
ing particular attention to the vicinity of the half-
moons; deburr if necessary.

•

Set the piston in cylinder 1 to approx. 90° before 
top dead centre 
(cylinder 1 = at timing end of engine).

L

 Note:

Clean the cylinder head bolts and the threads in the 
engine block. The bolts must screw easily into their 
tapped bores without the assistance of tools: chase 
the threads if necessary.

•

The sealing faces must be clean, flat and undam-
aged.

•

Place the cylinder head gasket in position; no 
holes or passages must be obstructed.

•

Place the cylinder head in position, noting the lo-
cating sleeves.

•

Oil bolts (1) and washers (2) and screw them in 
until sealed.

•

Check that the engine block and cylinder head 
gasket are correctly aligned; if necessary use a 
whetstone to remove protruding edges of the 
gasket.

•

Tighten the cylinder head screws in the correct 
sequence as shown to specified torque.

•

Install angle-of-rotation gauge, 

BMW No. 11 2 500

, with two Torx inserts T 50, 

BMW No. 00 2 630

.

•

Tighten the cylinder head screws in the correct 
sequence as shown through the specified addi-
tional angle of rotation.

•

Install the bucket tappets.

•

Install the camshafts (

a 

11.44).

•

Install the temperature sensor (

a 

61.15).

X 

Tightening torque:

Cylinder head screws
Initial torque ................................................. 20 Nm 
Additional angle of rotation................................ 90°
Camshaft bearing cap .................................. 10 Nm
Temperature sensor ..................................... 30 Nm

KR110270

1

2

KR110650

8

10

4

2

5

7

6

1

3

9

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands